Cluster-in-a-Box CLI Online Deployment - Red Hat Distribution

Duplicate Hosts

As of SingleStore Toolbox 1.4.4, a check for duplicate hosts is performed before SingleStore is deployed, and will display a message similar to the following if more than one host has the same SSH host key:

✘ Host check failed.host 172.26.212.166 has the same ssh
host keys as 172.16.212.165, toolbox doesn't support
registering the same host twice

Confirm that all specified hosts are indeed different and aren’t using identical SSH host keys. Identical host keys can be present if you have instantiated your host instances from images (AMIs, snapshots, etc.) that contain existing host keys. When a host is cloned, the host key (typically stored in /etc/ssh/ssh_host_<cipher>_key) will also be cloned.

As each cloned host will have the same host key, an SSH client cannot verify that it is connecting to the intended host. The script that deploys SingleStore will interpret a duplicate host key as an attempt to deploy to the same host twice, and the deployment will fail.

The following steps demonstrate a potential remedy for the duplicate hosts message. Please note these steps may slightly differ depending on your Linux distribution and configuration.

sudo root
ls -al /etc/ssh/
rm /etc/ssh/<your-ssh-host-keys>
ssh-keygen -f /etc/ssh/<ssh-host-key-filename> -N '' -t rsa1
ssh-keygen -f /etc/ssh/<ssh-host-rsa-key-filename> -N '' -t rsa
ssh-keygen -f /etc/ssh/<ssh-host-dsa-key-filename> -N '' -t dsa

For more information about SSH host keys, including the equivalent steps for Ubuntu-based systems, refer to Avoid Duplicating SSH Host Keys.

As of SingleStore Toolbox 1.5.3, sdb-deploy setup-cluster supports an --allow-duplicate-host-fingerprints option that can be used to ignore duplicate SSH host keys.

Network Configuration

Depending on the host and its function in deployment, some or all of the following port settings should be enabled on hosts in your cluster.

These routing and firewall settings must be configured to:

• Allow database clients (e.g. your application) to connect to the SingleStore aggregators

• Allow all nodes in the cluster to talk to each other over the SingleStore protocol (3306)

• Allow you to connect to management and monitoring tools

The service port values are configurable if the default values cannot be used in your deployment environment. For more information on how to change them, see:

• The cluster file template provided in this guide

• The SingleStore configuration file

• The sdb-toolbox-config register-host command

We also highly recommend configuring your firewall to prevent other hosts on the Internet from connecting to SingleStore.

Notes on Users and Groups

The user that deploys SingleStore via SingleStore Toolbox must be able to SSH to each host in the cluster. When singlestoredb-server is installed via an RPM or Debian package when deploying SingleStore, a memsql user and group are also created on each host in the cluster.

This memsql user does not have a shell, and attempting to log in or SSH as this user will fail. The user that deploys SingleStore is added to the memsql group. This group allows most Toolbox commands to run without sudo privileges, and members of this group can perform many Toolbox operations without the need to escalate to sudo. Users who desire to run SingleStore Toolbox commands must be added to the memsql group on each host in the cluster. They must also be able to SSH to each host.

Manually creating a memsql user and group is only recommended in a sudo-less environment when performing a tarball-based deployment of SingleStore. In order to run SingleStore Toolbox commands against a cluster, this manually-created memsql user must be configured so that it can SSH to each host in the cluster.

Minimal Deployment

SingleStore has been designed to be deployed with at least two nodes:

• A Master Aggregator node that runs SQL queries and aggregates the results, and

• A single leaf node, which is responsible for storing and processing data

These two nodes can be deployed on a single host (via the cluster-in-box option), or on two hosts, with one SingleStore node on each host.

While additional aggregators and nodes can be added and removed as required, a minimal deployment of SingleStore always consists of at least these two nodes.

Option 1: Command Line

You can deploy your SingleStore cluster on a single host using the sdb-deploy cluster-in-a-box command. This command will create two nodes: A Master Aggregator node that runs SQL queries and aggregates the results, and a single leaf node, which is responsible for storing and processing data. These two nodes form the most basic SingleStore cluster.

• The default port for the Master Aggregator can be changed by adding the --master-port option and specifying the desired port.

• The default port for the leaf node can be changed by adding the --leaf-port option and specifying the desired port.

sdb-deploy cluster-in-a-box --license <license> --version 8.1 --password <secure-password>

Note: You can retrieve the license from the Cloud Portal.

Option 2: Cluster File

This example is equivalent to sdb-deploy cluster-in-a-box, where a single-host cluster is created with two nodes: a Master Aggregator and a single leaf node.

Set package_type to either rpm for Red Hat distributions or deb for Debian distributions to download and deploy the appropriate singlestoredb-server.

license: <license-from-portal.singlestore.com>
memsql_server_version: 8.1
package_type: <rpm|deb>
hosts:
- hostname: 127.0.0.1
  localhost: true
  nodes:
  - register: false
    role: Master
    config:
      password: <secure-password>
      port: 3306
  - register: false
    role: Leaf
    config:
      password: <secure-password>
      port: 3307

Using this cluster configuration file, sdb-deploy setup-cluster:

1. Registers a single, local host to the cluster.

2. Installs the latest 8.1 version of singlestoredb-server on this host.

3. Creates a Master Aggregator node on port 3306 and sets the SingleStore password to the one specified in the cluster file.

4. Creates a leaf node on port 3307 and sets the SingleStore password to the one specified in the cluster file.

5. Run the following with the path to the cluster file as input.

   Shell

   Copy

   sdb-deploy setup-cluster --cluster-file </path/to/cluster-file>

Additional Deployment Options